HQ8251, HQ8250, HQ8241, HQ8240, HQ8200 EnglisH 4 indonEsia 19 34 BaHasa MElayu 49 65 Ting ViT 77 92 105 4 EnglisH introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips. com/welcome. Please read this user manual, as it contains information about the wonderful features of this shaver as well as some tips to make shaving easier and more enjoyable. important Read this user manual carefully before you use the appliance. Save the user manual for future reference. danger - Make sure the adapter does not get wet. Warning - Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. - The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this causes a hazardous situation. - This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. - Children should be supervised to ensure that they do not play with the appliance. EnglisH Caution 5 - Never immerse the shaver in water. - Charge (all types except HQ8200), use and store the shaver at a temperature between 10°C and 35°C. - Always put the protection cap on the shaver to protect the shaving heads when you are travelling. - The shaver and the other accessories are not dishwasher-proof. - Never use water hotter than 80°C to rinse the shaver. - Do not use the shaver in the bath or in the shower. - Only use the adapter supplied. - Do not use the shaver or the adapter if it is damaged. - If the adapter is damaged, always have it replaced with one of the original type in order to avoid a hazard. Compliance with standards - The shaver complies with the internationally approved IEC safety regulations and can be safely cleaned under the tap. - This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. general - The adapter transforms 100-240 volts to a safe low voltage of less than 24 volts. 6 EnglisH overview A B C F G D E H K I J a B C d E F g Protection cap Shaving unit Shaving unit release button Shaver on/off button with power-on symbol Display (all types except HQ8200) Trimmer Cleaning brush EnglisH H Storage pouch (your pouch may differ from the one shown in the figure) i Adapter J Small plug K Bathroom stand (HQ8251/HQ8250 only) The display (all types except HQ8200) 7 The HQ8251, HQ8250, HQ8241 and HQ8240 have different displays, which are shown in the figures below. - HQ8251/HQ8250 - HQ8241/HQ8240 Charging indication Charging takes approx. 60 minutes. A fully charged shaver provides up to 17 cordless shaves. - When the shaver is charging, the CHARGE light is on continuously. 'Battery fully charged' indication - When the battery is fully charged, the CHARGE light starts flashing. Note:When you disconnect the shaver from the mains, the CHARGE light stops flashing. 8 EnglisH 'Battery low' indication (HQ8251/HQ8250 only) Note: If the rechargeable battery runs low during shaving, you can connect the shaver to the mains to finish the shave. - When the battery is almost empty (when there are only 5 or fewer shaving minutes left), the LOW light goes on. - When you switch off the shaver, the LOW light flashes a few seconds. Charging (all types except HQ8200) Note:The HQ8200 is not rechargeable. HQ8251/HQ8250: Charge the shaver when the LOW light goes on. HQ8241/HQ8240: Charge the shaver when the motor stops or starts running slower. It takes approx. 60 minutes to fully charge the battery. When you charge the shaver for the first time or after a long period of disuse, let it charge for 12 hours. Tip:To optimise the battery capacity, fully charge the shaver and then use it normally until the battery is completely empty. Repeat this process three times in a row. If you optimise the battery capacity in this way, you can also charge the shaver in between shaves, even if the battery is not completely empty yet. A fully charged shaver provides up to 17 cordless shaves. If you have a heavy beard, the shaver may provide less than 17 cordless shaves. The shaving time may also vary over time, depending on your shaving behaviour, cleaning habits and beard type. EnglisH Charging the shaver Do not charge the shaver in a closed pouch. 1 Put the small plug in the shaver. 2 Put the adapter in the wall socket. , The CHARGE light goes on. using the shaver Note:The HQ8200 can only be used directly from the mains. Note for all types except HQ8200:You can also use the appliance without charging. Simply connect the appliance to the mains. shaving 1 HQ8200: Put the small plug in the shaver and put the adapter in the wall socket. 9 2 Press the on/off button once to switch on the shaver. , The power-on symbol in the on/off button lights up. 3 Move the shaving heads over your skin. Make both straight and circular movements. - Shaving on a dry face gives the best results. - Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system. 4 Press the on/off button once to switch off the shaver. 5 HQ8200: Remove the adapter from the wall socket and pull the small plug out of the shaver. 10 EnglisH 6 Clean the shaver (see chapter `Cleaning and maintenance'). Trimming You can use the trimmer to groom your sideburns and moustache. 1 HQ8200: Put the small plug in the shaver and put the adapter in the wall socket. 2 Press the on/off button once to switch on the shaver. , The power-on symbol in the on/off button lights up. 3 Push the trimmer slide downwards to open the trimmer. , You can now start trimming. 4 After trimming, close the trimmer (`click') and switch off the shaver. 5 HQ8200: Remove the adapter from the wall socket and pull the small plug out of the shaver. Cleaning and maintenance Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance. - Clean the shaver after every shave for optimal shaving performance. - Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. - You can clean the bathroom stand (HQ8251/ HQ8250 only) and the outside of the shaver with a damp cloth. EnglisH 11 Note:Water may leak from the socket at the bottom of the appliance when you rinse it.This is normal and not dangerous. Cleaning the shaving unit under the tap 1 Switch off the shaver and disconnect it from the mains. 2 Press the release button to open the shaving unit. 3 Rinse the shaving unit and hair chamber under a hot tap for some time. - Make sure that you clean the inside as well as the outside of the shaving unit. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. 4 Close the shaving unit and shake off excess water. Never dry the shaving unit and the hair chamber with a towel or tissue, as this may damage the shaving heads and the coupling spindles. 5 Open the shaving unit again and leave it open to let the shaver dry completely. 12 EnglisH Cleaning the shaving unit with the brush supplied 1 Switch off the shaver and disconnect it from the mains. 2 Press the release button to open the shaving unit. 3 Turn the lock anticlockwise (1) and remove the retaining frame (2). 4 Clean the shaving heads with the brush supplied. Each shaving head consists of a cutter and a guard. Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored. 5 Put the shaving heads back into the shaving unit. 6 Put the retaining frame back into the shaving unit and turn the lock clockwise. 7 Close the shaving unit. Note: If the shaving unit does not close smoothly, check if you have positioned the shaving heads properly and if the retaining frame is locked. EnglisH 13 Cleaning the trimmer with the brush supplied Clean the trimmer every time you have used it. 1 Switch off the shaver and disconnect it from the mains. 2 Push the trimmer slide downwards to open the trimmer. 3 Clean the trimmer with the short-bristled side of the cleaning brush. Brush up and down along the trimmer teeth. 4 Close the trimmer (`click'). Tip: For optimal trimming performance, lubricate the trimmer teeth with a drop of sewing machine oil every six months. storage There are several ways to store the shaver or to take it with you when you travel: - put the protection cap on the shaver to prevent damage. - store the appliance in the pouch supplied. - HQ8251/HQ8250: store the shaver in the bathroom stand. 14 EnglisH Replacement For maximum shaving performance, we advise you to replace the shaving heads every two years. Replace damaged shaving heads right away. Only replace the shaving heads with original HQ9 Philips Shaving Heads. 1 Switch off the shaver and disconnect it from the mains. 2 Press the release button to open the shaving unit. 3 Turn the lock anticlockwise (1) and remove the retaining frame (2). 4 Remove the shaving heads and place new ones in the shaving unit. Make sure that the projections of the shaving heads fit exactly into the recesses. 5 Put the retaining frame back into the shaving unit and turn the lock clockwise. 6 Close the shaving unit. Note: If the shaving unit does not close smoothly, check if you have positioned the shaving heads properly and if the retaining frame is locked. accessories The following accessories are available: - HQ9 Philips Shaving heads EnglisH 15 - HQ110 Philips Shaving Head Cleaning Spray (not available in some countries) - HQ8010 car cord. Environment - Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment. - All types except HQ8200: The built-in rechargeable shaver battery contains substances that may pollute the environment. Always remove the battery before you discard or hand in the shaver at an official collection point. Dispose of the battery at an official collection point for batteries. If you have trouble removing the battery, you can also take the appliance to a Philips service centre. The staff of this centre will remove the battery for you and will dispose of it in an environmentally safe way. Removing the rechargeable shaver battery (all types except HQ8200) Only remove the rechargeable battery when you discard the shaver. Make sure the rechargeable battery is completely empty when you remove it. 1 Disconnect the shaver from the mains. 2 Let the shaver run until it stops and undo the two screws in the back of the shaver. 16 EnglisH 3 Undo the two screws in the hair chamber. 4 Remove the back panel. 5 Remove the two side panels. 6 Bend the 4 hooks aside and take out the power unit. Be careful, the hooks are sharp. 7 Undo the three screws in the power unit. 8 Remove the power unit cover with a screwdriver. EnglisH 17 9 Remove the battery. Be careful, the battery strips are sharp. Do not connect the shaver to the mains again after you have removed the rechargeable battery. guarantee & service If you need service or information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Consumer Care Centre in your country (you find its phone number in the worldwide guarantee leaflet). If there is no Consumer Care Centre in your country, go to your local Philips dealer. guarantee restrictions The shaving heads (cutters and guards) are not covered by the terms of the international guarantee because they are subject to wear. Troubleshooting 1 The shaver does not shave as well as it used to. - The shaving heads may be damaged or worn. Replace the shaving heads (see chapter `Replacement'). - Long hairs may be obstructing the shaving heads. Clean the cutters and guards with the brush supplied (see chapter `Cleaning and maintenance'). 2 The shaver does not work when I press the on/off button. - All types except HQ8200: The battery may be empty. Recharge the battery (see chapter `Charging') or connect the shaver to the mains. - HQ8200: The shaver is not connected to the mains. Put the small plug in the shaver, put the 18 EnglisH adapter in the wall socket and press the on/off button again. - The temperature of the shaver may be too high. In this case, the shaver does not work. As soon as the temperature of the shaver has dropped sufficiently, you can switch on the shaver again. indonEsia 19 Pendahuluan Selamat atas pembelian Anda dan selamat datang di Philips! Untuk memanfaatkan s ...